Search:

Type: Posts; User: pfrench

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    7,266

    The audio delay is, erm adjustable. It's in the...

    The audio delay is, erm adjustable. It's in the config file. It has been "tuned" to be approx. a two frame delay, to match video through, so the outputs remain synchronized.
  2. Replies
    76
    Views
    9,713

    I believe this has been fixed. TricCster's been...

    I believe this has been fixed. TricCster's been taking much of our time (obviously) but the gains made in the TriCaster will translate to gains for the VT[4].
  3. Replies
    9
    Views
    958

    More info: The minimum possible latency to...

    More info:

    The minimum possible latency to output on VT is 2.0 frames. If all your inputs and the VT are genlocked together, it will be 2.0 frames, forever.

    If a video input is not genlocked...
  4. Replies
    9
    Views
    958

    If the Horita unit isn't synced to anything, I'd...

    If the Horita unit isn't synced to anything, I'd just run composite outs from the SX-8(4) to the cameras, this will give you the lowest possible latency.

    Trick: If you're not using VT component...
  5. Replies
    7
    Views
    1,613

    Can you give a set of steps that cause this...

    Can you give a set of steps that cause this message every time?
  6. Replies
    76
    Views
    9,713

    Could you check your IDE controllers to see if...

    Could you check your IDE controllers to see if they are in PIO (instead of DMA) mode?
  7. Replies
    15
    Views
    2,069

    The audio glitch in the software. It resulted...

    The audio glitch in the software. It resulted from external events causing performance hits on the RTME. The "hit recovery" code had a small problem that would cause the software to lose track of...
  8. Replies
    15
    Views
    2,069

    RE: audio issues with VT[4]

    This problem has been fixed and will be in the next update.
  9. Replies
    15
    Views
    1,766

    Found and fixed this one today. It will be...

    Found and fixed this one today. It will be available in the next update. Thank you for your patience.
  10. Replies
    3
    Views
    501

    We use Antec TruePower supplies. They're more...

    We use Antec TruePower supplies. They're more expensive but much better built. I"ve had bad power supplies kill motherboards.
  11. Replies
    27
    Views
    4,266

    Each "Progressive" Frame in the DVE contains a...

    Each "Progressive" Frame in the DVE contains a DVE for both the odd and even field at the same instant in time.

    When a DVE is performed in the switcher, the slowest it should be played is at four...
  12. Replies
    27
    Views
    4,266

    apology in advance for the un-edited rambling...

    apology in advance for the un-edited rambling answer



    Awesome!!!



    The DVE Frame rate needs to be double the field rate so the DVE can be "played" inside the switcher and have smooth,...
  13. Thread: Audio Problem

    by pfrench
    Replies
    19
    Views
    2,459

    The procedure: 1. Turn on volume for an...

    The procedure:

    1. Turn on volume for an external audio source so it passes through to program out.
    2. Kill VT/RTME

    leaves the VT card in an un-monitored hardware pass-through state. If you...
  14. Thread: Audio Problem

    by pfrench
    Replies
    19
    Views
    2,459

    The next time this happens could you try: 1....

    The next time this happens could you try:


    1. Turn on an analog audio source
    so live (external) audio is passing through

    2. Exit VT

    3. Kill WinRTME
  15. Replies
    1
    Views
    783

    >Second - should I cancel winrtme.exe prior >to...

    >Second - should I cancel winrtme.exe prior >to launching VT2 before a live event

    You can, Killing WinRTME and all other VT programs will "Reset" the VT's internal state. It is the equivalent of...
  16. Very true. Also remember if it comes in via...

    Very true.
    Also remember if it comes in via firewire it has to be decoded into video by the computer. This takes some time. Coming in via analog you get the VT's 2-3 frame delay "through" and no...
  17. Replies
    11
    Views
    1,046

    There currently are no provisions for providing...

    There currently are no provisions for providing closed caption information in the VT's output .
  18. Replies
    1
    Views
    1,456

    This is one of those situations where we...

    This is one of those situations where we basically had to vote on what the behavior of windows audio volume would be. There are basically two levels of control for Windows audio volume on VT2/VT3...
  19. Replies
    10
    Views
    1,565

    It has never happened to me. This issue may have...

    It has never happened to me. This issue may have been fixed in VT3. But at least the info you gave me gives me something to look at.
  20. Replies
    10
    Views
    1,565

    So you can adjust the U/V offset differences for...

    So you can adjust the U/V offset differences for component, select the same camera on Main and Preview, to a bunch of Takes and the signals look the same.... Then, much later, you start selecting...
  21. Replies
    10
    Views
    1,565

    Yes, but there are still two analog video paths...

    Yes, but there are still two analog video paths into the VT. They have some differences between them which can only be compensated for in the "Preferences" area.

    If you select the same Component...
  22. Thread: winrtme.exe II

    by pfrench
    Replies
    16
    Views
    2,788

    I really can't determine what might be wrong...

    I really can't determine what might be wrong unless I get the output from "newtekrtme.exe"

    If you can't run it by double clicking it. Open a "command prompt" and "cd" to the VT3 Drivers...
  23. Replies
    10
    Views
    1,565

    You probably need to adjust the Component U/V...

    You probably need to adjust the Component U/V deltas (forgot what the names are) in Preferences. It allows you to calibrate for the differences between the separate analog video input paths.

    In...
  24. Thread: winrtme.exe II

    by pfrench
    Replies
    16
    Views
    2,788

    Go into the "drivers" folder and double click...

    Go into the "drivers" folder and double click newtekrtme.exe until it stays open. Copy/paste its output here.
  25. Thread: winrtme.exe

    by pfrench
    Replies
    12
    Views
    5,678

    If you can reliably reproduce the problem it...

    If you can reliably reproduce the problem it would help a great deal if you sent in a detailed list of steps to take to reproduce the problem.
Results 1 to 25 of 37
Page 1 of 2 1 2