PDA

View Full Version : Mackie 1202 VLZ Pro Audio Mixer - $200 plus shipping



randallstu
08-03-2006, 02:24 PM
Mackie Mixer 1202 VLZ Pro - $200 plus shipping
Call 503-524-1780 or
email: [email protected]

Excellent condition and very low hours

0.0007% Total Harmonic Distortion. The lowest ever in any compact mixer.

Flat response. Not only are XDR mic preamps flat within a tenth of a dB across the bandwidth of any known microphone, but are also only 3dB down at an astonishing 192kHz!

Super-low intermodulation distortion at very high operating levels thanks to instrumentation-style balanced differential architecture, linear biasing, and use of DC-coupled pole-zero-cancellation constant current that frees the mic preamp from power supply fluctuations.

Think of the 1202 as an ultra-premium, esoteric mic preamp...that just happen to have really excellent compact mixers attached.

Features
Ultra-low noise, highest headroom in its class

4 new precision-engineered XDR(tm) Extended Dynamic Range premium studio-grade mic preamps with: ultra-wide 0-60dB gain range, 130dB dynamic range for 24-bit, 192kHz sampling rate inputs, +22dBu line input handling, distortion under 0.0007% (20Hz-20kHz)

Advanced DC pulse transformer RF rejection

12 line inputs (4 mono, 4 stereo pairs)

Separate RCA-type tape/CD inputs and tape outputs (unbalanced)

2 aux sends with 15dB of extra gain above Unity

Constant-loudness pan pots

PFL Stereo in-place Solo on each channel

2 stereo aux returns with EFX to Monitor

Aux 1 master with Monitor/Post assign

3-band active EQ (80Hz, 2.5kHz, 12kHz)

18dB/oct. 75Hz Lo Cut filter eliminates stage rumble, wind noise, P-pops, and low frequency recording studio room resonances
Extra ALT 3-4 stereo bus for sub-mixes, separate recording, monitor, and 'mix minus' feeds

Control Room/Phones multi-input source matrix

Phantom power for premium condenser mics

Rugged steel chassis, sealed rotary controls

Built-in power supply no wall wart!
Technical Description

Main Mix Noise
20Hz-20kHz bandwidth, 1/4 in. Main out, channels 1-4 Trim @ unity gain, channel EQs flat, all channels assigned to main mix, channels 1 and 3 pan left, 2 and 4 pan right

Main Mix knob fully counterclockwise, channel Gain knobs down: -100dBu

Main Mix knob unity, channel Gain knobs down: -86.5dBu
(90dB Signal to Noise Ratio, ref +4dBu) Main Mix knob @ unity, channel

Gain knobs @ unity: -84.5dBu

Total Harmonic Distortion (THD)
1kHz @ +14dBu, 20Hz-20kHz
Mic in to Main out: 0.0007%

Attenuation (Crosstalk)
1kHz relative to 0dBu, 20Hz-20kHz bandwidth, Line in, 1/4" Main Out, Trim @ unity
Main Mix knob down: -85dBu
Channel Alt/Mute switch engaged: -84dBu
Channel Gain knob down: -83dBu

Frequency Response
Any input to any output
20Hz to 60kHz: +0dB/-1dB
10Hz to 100kHz: +0dB/-3dB

Equivalent Input Noise (EIN)
Mic in to Insert Send out, max gain
150 ohm termination: -129.5dBm unweighted

Common Mode Rejection (CMR)
Mic in to Insert Send out, max gain
1kHz: better than 90dB

Maximum Levels
Mic in: +22dBu
Tape in: +16dBu
All other inputs: +22dBu
Main Mix XLR out: +28dBu
All other outputs: +22dBu
Impedances
Mic in: 1.3 kilohms
Channel Insert return: 2.5 kilohms
All other inputs: 10 kilohms or greater
Tape out: 1.1 kilohms
All other outputs: 120 ohms

EQ
High Shelving: 15db @ 12kHz
Mid Peaking: 12dB @ 2.5kHz
Low Shelving: 15db @ 80Hz

Power Consumption
120VAC, 50/60Hz, 25 watts

Weight
6 lbs., 8 oz. (3 kg)