Search:

Type: Posts; User: jcupp

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    4
    Views
    526

    The legends on the buttons are on a thin plastic...

    The legends on the buttons are on a thin plastic chip under the clear cover. They can be removed. I'm pretty sure the buttons are made by keytronics.
  2. Replies
    30
    Views
    1,150

    You just need a small Ethernet switch at the...

    You just need a small Ethernet switch at the camera end.
    Like this
  3. Replies
    5
    Views
    356

    Our software driven tally controllers should work...

    Our software driven tally controllers should work on the NC1 I/O.
  4. Replies
    5
    Views
    356

    Our (metaSETZ) TLC-8D controller will work with...

    Our (metaSETZ) TLC-8D controller will work with any NewTek 15 pin tally port. With the I/O module you'll get 4 program tallys. You can also use a TLC4S or 8S which are software driven via USB. You...
  5. I'd pop the cover and make sure all the fans are...

    I'd pop the cover and make sure all the fans are working. You may have lost one. It also may be you have a fan with a bad bearing that's getting noisy.

    TC410 fans: Two fans (stacked) in front of...
  6. It should work but no one from NewTek is likely...

    It should work but no one from NewTek is likely to say so.
  7. I've opened up a Mini to take a look and it's...

    I've opened up a Mini to take a look and it's pretty scary inside, and I don't scare easy. Be very careful if you decide to swap drives.
  8. Replies
    6
    Views
    447

    A lot of cheap converters don't do 1080i They do...

    A lot of cheap converters don't do 1080i They do 1080p or 720p. Try changing everything over to 720p and see if you get a signal.
  9. Thread: Audio Techniques

    by jcupp
    Replies
    4
    Views
    446

    Feed media player audio to the Aux output ONLY....

    Feed media player audio to the Aux output ONLY. Run the Aux out to the external mixer.

    You can use an SDI demuxer to gain another analog audio outputs to do the same with NDI sources etc. Mix...
  10. http://clonezilla.org/downloads/download.php?branc...

    http://clonezilla.org/downloads/download.php?branch=stable

    Use this to write the ISO to a bootable flash drive:
    http://www.isotousb.com/
  11. Replies
    2
    Views
    360

    Since this is a Mini and you only have one set of...

    Since this is a Mini and you only have one set of audio outputs you have to do this sort of sideways. The easiest way to do this is to run the headphone jack to the external mixer. Then both mute and...
  12. Replies
    7
    Views
    873

    Just a quick update for the record. NewTek found...

    Just a quick update for the record. NewTek found the BMD bug and has an update coming to Connect Pro that will prevent the memory issue!
  13. Thread: 2 dead 460s

    by jcupp
    Replies
    5
    Views
    657

    That's not gonna work in a 460.

    That's not gonna work in a 460.
  14. Thread: 2 dead 460s

    by jcupp
    Replies
    5
    Views
    657

    The H77 chipset boards are indeed made from...

    The H77 chipset boards are indeed made from unobtanium. I don't think an H97 board will boot with the H77 drivers. I've got an email into NewTek's parts dept right now as my demo machine has the same...
  15. Replies
    7
    Views
    873

    That's the weird thing. I built several identical...

    That's the weird thing. I built several identical machines and only one of them had the issue until I played with the cards. I was just chalking it up to "BMD, what you gonna do?" until denver.root...
  16. Replies
    7
    Views
    873

    I started by pulling the Mini Monitor output card...

    I started by pulling the Mini Monitor output card (I'd heard reports of small memory leaks) and the problem disappeared. At the time I thought it might be caused by the order in which the BMD cards...
  17. Thread: NDI spec?

    by jcupp
    Replies
    11
    Views
    1,570

    The NDI standard is open (the license is free)...

    The NDI standard is open (the license is free) the source code is not.
  18. Replies
    1
    Views
    298

    Call me tomorrow I think I can fix you up.

    Call me tomorrow I think I can fix you up.
  19. Replies
    7
    Views
    631

    Vimeo or something like it might be a solution.

    Vimeo or something like it might be a solution.
  20. Replies
    2
    Views
    533

    I think here's a TV Technology Best In Show award...

    I think here's a TV Technology Best In Show award laying around in the booth also.
    ...
  21. I'm guessing most off-the-shelf PTZ cameras won't...

    I'm guessing most off-the-shelf PTZ cameras won't operate properly on their side because I'm sure the pan mechanism isn't designed to fight gravity. You might need a more robust robotic camera mount...
  22. Replies
    8
    Views
    621

    I've found a Killawatt a useful device for UPS...

    I've found a Killawatt a useful device for UPS planning. It can measure actual VA draw of stuff plugged into it. Runs $30 or so on Amazon.
  23. Replies
    7
    Views
    873

    NDI Connect Pro Memory Leak?

    I've built several machines to run NDI Connect Pro and they are working pretty well except for one machine. There appears to be a massive memory leak that causes the machine to allocate all the...
  24. Replies
    2
    Views
    277

    I's guess it's the power supply. Burnt smell =...

    I's guess it's the power supply. Burnt smell = not good. They are generally not an issue but infant failures are not unheard of.
  25. Replies
    38
    Views
    3,468

    They have those contact your local dealer, or...

    They have those contact your local dealer, or give Digital Arts a call :)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4